Offering a Selection of Reliable Project Execution Solutions

We are responsible for successfully completing a variety of high-caliber challenging electrical, automation and controls, and communications projects resulting in improvements to safety, reliability, performance, and profitability. The services we provide include but are not limited to the following:

· PLC and DCS Programming and integration

· Communications Architecture Design

· Control Philosophy and Narrative Development

· Alarm Management Strategies 

· Process Control Definition

· HMI Design

· Control System Integration

· Control panel Design

· SCADA and RTU System Installation and Testing

· SCADA Systems and Computer Networking

· Control System Commissioning

We provide comprehensive services from project initiation phase to ALARP all technical safety related services which included but not limited to the following:

· Safety Case Development

· Health, Safety, and Environmental Impact Assessment

· Major Accident Hazard (MAH) Identification, Assessment, and Management

· Emergency Response Plans

· Bowtie Elements Identifying and Modeling

· HSEMS

· Hazard Identification

· Fire Consequence Analysis

· Explosion Consequence Analysis

· Smoke and Gas Ingress Analysis

· Toxic Hazard Analysis

· Collision Hazards assessment

· Dropped Object Study

· External Loads

· TR and EERA Analysis

· QRA: The Quantitative Risk Analysis reports

· Continuous Improvement

· Process Safety Management (PSM)

We implement and strive for the mitigation management of hazards that can give rise to major accidents involving release of potentially dangerous materials, energy (such as fire or explosion), or both. We maintain and carry out asset studies and make sure that they perform its required function effectively and efficiently whilst safeguarding life and environment.

At Octal Energy Services Ltd, we manage PSM for clients on three main principals:

· Establishing comprehensive process safety management framework

· Producing and or adherence to comprehensive guidelines to manage process safety for each Element of the PSM framework.

· Carry out in-depth survey based on the PSM framework or verification providing from inception of the project to it final order fulfillment (Asset to operation).

We undertake the following elements to mitigate PSM risk in our project deliveries:

· Asset Technical INTEGRITY review and studies

· Design INTEGRITY review and studies

· Operating INTEGRITY review and studies

· Hardware Barrier Verification 

· Review critical work activities (i.e. start-ups/shutdowns) and equipment conditions

· List any deficiencies and develop and implement corrective actions

· Dead-leg surveys and recommendation for alternation and possible solutions

· Review critical work activities (i.e. start-ups/shutdowns) and conditions monitoring

· Write-up and train how to use procedure and desk top instruction for critical systems

· Standard Operating Procedure (SOP) write-ups and field training for artisans and operators.

· Artisan and operators’ technical competency and behaviors training “working with fit for purpose systems”

· Safety Critical Elements (SCEs) and performance standards assessment identifies HSECES required by code.

· Identifying and the managing hazards that can give rise to major process incidents involving the release of dangerous materials (e.g. H2S) and or energy (e.g. fire or explosion)

· HSE-MS audits

· Technical compliant review and audits with the relevant standards, frameworks, procedures, and preparation of audit Corrective Action Plans (CAPs)

· Extended equipment inspection and recommendation for correction action.

· Static Equipment Integrity Management

· Demonstrate ALARP (retro HAZOP, CHAZOP, IPF, FERM, and OBRA)

· PSM competence documents development

· Set up asset integrity and Process Safety Management (PSM) KPIs and monitoring and reporting against set KPIs by using state-of-the-art computer and monitoring systems

· Annual compliance check with the work process (TR-MIE) and comprehensive report to client.

· Third-party verification of hardware barrier status

We make sure that client projects deliver on their original promises in terms of production, reliability, and availability, and that it is fully ready prior to start-up and final handover during the operations phase.

We also undertake complete operation readiness tasks from the Project Execution Plan (PEP) to flawless delivery of the project. Our OR&A Team oversees all the operational deliverables to the Project and Asset Team by reviewing and incorporating operational requirements for a project in its scope and ensuring their implementation during all phases of the project delivery.

Our primary accountabilities for this project are to:

· Define and build on the projects’ operations philosophy and requirements

· Prepare the OR&A plans using the related standards, processes, tools, and systems to ensure their incorporation in the Project Execution Plan (PEP) and full implementation

· Ensure that Flawless Project Delivery is implemented and realized on assigned projects at each stage and conduct Value Assurance Reviews (VAR).

· Prepare plans and procedures for safe and cost-effective commissioning and start-up as per CSU logic, plan, and requirements. This includes the taring of operators and technicians.

· Provide assistance and criterions for controlled ramp-up to steady state operations

· Review and audit the total reliability a technical integrity of the operating facilities asset management to ensure that they are fully prepared to take the project into the operations phase of its life.

Our team and associates have extensive skills in the operation and maintenance of H2S plants, systems, and equipment. We also have the following in-depth experience and knowledge available on client request:

· Outlining specific design requirements, material selection, and rating of pipe and equipment used for sour service versus the impact operability and maintainability

· Identify what QRA credits can be obtained via the higher-level QA and QC (e.g. welding procedures) by reviewing and formatting documents, guidelines, procedure, and checklists

· Defining leak mitigation measures and plans

· H2S equipment selection criteria as per clients established specifications and guidelines

· Preparing and training for standards and procedures pertaining to H2S operations

· Providing procedures to the use of enclosures as barriers in relation to safe distances

· Outlining minimum people competency requirements for H2S area work, prepare training programs and requirements, and provide technical training

· Defining operations and maintenance philosophy for our services, H2S protection philosophy and recovery measure, operation and maintenance H2S detection systems

· Provide typical Reliability, Availability, and Maintainability (RAM) studies and prepare documents for our service plants versus the level of automation required (fit for purpose) study.

· Preparing procedures for Simultaneous and Concurrent Operations (SIMOPS) and chart establishing associated with the Manual Of Permitted Operation (MOPO)

· Preparation of emergency response requirements and procedures

· Process optimization studies and solutions after startups of the facilities and the bottlenecking of installed systems

Control system tuning and optimization of the production versus design criteria of the installed equipment on-site 

We provide conversional and non-conversional enhanced oil recovery solutions and turnkey operations for water, gas, polymer, CDS, stream, and CO2 injection and flooding systems) through universities, research centers, test labs, and proven field trial operators.

Source: Waterflood Manual Chapter 13 – Chemical EOR

The EOR services we offer are covered for the following:

· Polymer (ASP): polymer injection. A process that works by increasing water viscosity and improving the oil-water mobility ratio.

· Surfactant injection, which change the oil-water interfacial tension, leading to significantly lower residual oil saturations left after floods

· Combinations or variations of Alkaline-Surfactant

· Condensing solvents such as CS2 and CDS

· Enhanced Gas Recovery (EGR)

· Permeability layers which divert fluids into low permeability layers

· Miscible Gas (CO2)

· Foam Flooding. Foam reduces gas mobility more

· Steam Foam

· CSS, SAGD, and Steam

· Steam solvent flooding and injection

· Steam flood including injection of the superheated stream for deep reservoirs and high viscous oil

· Solvent + steam flooding

· Drive + pilots technologies

· Sustainable and renewable and energy mix solutions

Our innovative solutions for sustainable energy mix for any clients through in-house developed technologies or by involving our associate strategy partners and universities where R&D work are successfully achieved through prototype projects.

We fully understand health, environment, and equity as the evidences of the connections between the environment and health are well-established. The World Health Organization (WHO) estimates that environmental factors account for 24% of the world’s burden of disease and 23% of all deaths.

By expanding clean, green sources of energy such as wind, water, solar, biomass, and biogas, our solutions can balance and reduce health-environment equilibrium.

The renewable energy mix may be selected from the following types of energy sources and implementing the following solutions can reduce double carbon footprint:

· Wind 

· Solar

· Wave 

· Tidal 

· Geothermal 

· Biomass 

· Bio fuel 

· Fossil fuels (oil, gas and associated products) 

· Emerging technologies (fusion, battery technology, smart-gravitation, etc.)

· Power factor improvement and energy saving, thereby reducing carbon footprint

· Building Energy Management

We help any client with the following:

· Setting up an Integrated Power Supply Plan (IPSP)

· Balancing supply mix that aims to be reliable, modern, clean, and cost-effective while building on the gains achieved through Green Energy

· Producing electricity from particular energy sources and generation technologies

· Increasing generation capacity from alternative and renewable energy sources

· Developing and implementing conservation measures for plant, oil, and gas production and buildings

Creating and training the local workforce to undertake clean energy jobs 

As industrial economies mature and grow in both scale and complexity, the scale and nature of the services required to support their continued successful development also needs to develop.

· Simple wastes become more complex

· Process efficiency and maximizing recovery become more critical to a business’ success

· The sheer scale of operations means that managing the wastes and emissions which are the unintended consequence of mature, vibrant, successful, industrialized nations is an increasing challenge

We believe that throughout the region, there is a real and growing need for advanced expertise and technology in the field of specialist waste management, including the recovery of value from waste products. We also know that this market is currently underserved.

We have particular expertise in:

· Oil and gas waste recovery

· Mine waste recovery

· Liquid waste treatment and recovery

· Domestic waste management

Energy recovery 

We offer a unique service towards the design and implementation of customer requirements. Our team has a reputation of minimizing risks through safe, professional, and versatile high-quality project management techniques.

These techniques include Earned Value Management (EVM), Program Evaluation and Review Technique (PERT), Critical Path Analysis, and many others. All these are achieved thanks to our considerable expertise in project management. 

This means that whilst each company division operates as an autonomous service in its own right, they are, in conjunction within the Project Services Division. These divisions are vital contributors to the company's ability to offer completely integrated turnkey systems.

We improve our clients’ operations and processes through the following services:

· Improved reliability saves valuable lost production time

· Immediate local and remote access to the status of the plant allows faster responses to problems

· Improved control over production plant and equipment leads to consistent quality of the final products

· Information logging to permit detailed analysis leads to improved product quality and process efficiency

Our staff has experience in all kinds of DCS, PLC and minicomputer-based systems for a variety of applications across a breadth of industries including:

· Oil and Gas

· LNG and Utilities

· Mineral and Refining

· Water and Chemical

· Power, Boiler House, and Cogeneration Plants

· Food and Beverages

· Wellhead, SCADA, Radio Systems, and Truck Docks

· Marine, Shipping, and Ship-Loading Arms

Our services include:

· Fault diagnosis, maintenance, and enhancements of existing systems

· Hardware and software supply

· Consultancy requirements, design, and implementation

· System analysis and functional safety program testing including FAT, SAT, and IHAT

· Programming, graphics design, and migration

· On-going on-site and remote support

· Flawless commissioning, start-up, and manpower services

· Service vans equipped to carry out on-site instrument repair, re-calibration, and certification to meet customers’ quality control requirements.

· Maintenance contracts

· Address instrument calibration needs with an on-site contract. A regular visit from one of our service engineers will give reliable, accurate, and continuous operation of your site instrumentation.

· 24/7 service

· Our engineers are available 24 hours a day to provide continued operations on your process

We provide highly skilled commissioning personnel that have extensive knowledge and experience to carry out all stages of the pre-commissioning process, from point-to-point wiring checks, function checks, and loop checks down to the final handover of systems.

We also offer commissioning support using designated personnel to meet your specific operational requirements, providing specialist assistance with fault finding, electrical systems, technical guidance, and process and system hand-over.

We have a team of factory-trained field service technicians which can be made available on a 24-hour call out basis. Our service personnel can also provide training courses in-house or at the customer’s facility. We provide complete services from FAT up to SAT and documents. 

We have fully trained and certificated personnel from various disciplines on both short and long-term contracts. Our team of professionals include:

· Engineers

· Instrument and Electrical Technicians

· DCS, PLC, and SCADA Programmers and Testing Engineers